A new approach to assessing the performance of asphalt concrete at low temperatures and a spray-applied, high-performance concrete for bridge maintenance – the road construction industry is exploring new technologies and materials that researchers at Riga Technical University (RTU), in close collaboration with colleagues at the Swiss Federal Laboratories for Materials Science and Technology (Empa), are developing as part of the Swiss–Latvian cooperation program «Applied Research» project LACHMAT.
Some of the concrete bridge structures were built in the middle of the last century; their technical condition is affected by increased traffic loads, freeze-thaw cycles, corrosion, and the general aging of concrete structures. The result is visible to everyone – deteriorated steel protective coating, exposed reinforcement, and corrosion of steel reinforcement elements, says Andrejs Kavlaks, a doctoral student at the Institute of Sustainable Building Materials and Engineering Systems, Faculty of Civil and Mechanical Engineering, Riga Technical University (RTU), speaking at the annual road industry conference organized by the State Joint Stock Company «Latvijas Valsts ceļi» («Latvian State Roads»). Together with his colleagues in the LACHMAT project, he is researching and developing a high-performance sprayed concrete that would extend the service life of transportation infrastructure and reduce the need for reconstruction.
The conference is attended by heads and leading specialists from the road administrations of Latvia, Lithuania, Estonia, and Poland, as well as industry and local government representatives, officials from state institutions, and experts from various fields of the road sector: traffic safety, road maintenance, construction, and other specialists from Latvia and abroad.

Photo: “Latvijas Valsts ceļi”
Ultra-high-performance concrete contains very fine aggregate and cementitious materials. This means that the material is very dense, with few pores, resulting in minimal permeability to water and salts, and limited freeze-thaw reactions. To reinforce the material, steel or polymer fibers are used, which help increase flexural and compressive strength and improve crack resistance, explains the RTU doctoral student. He also explains how the material is sprayed, including in hard-to-reach places, and demonstrates experiments that researchers have already conducted in Latvia in collaboration with the company «Reaktīvs». Citing estimates and studies, A. Kavlaks estimates that the use of the material will be economically justified in the long term, as it lasts significantly longer, application is faster, thereby reducing labor and equipment costs, and dismantling is also more economical, as less material needs to be disposed of. The first examples of the use of high-performance sprayed concrete in the maintenance of bridges and tunnel-type infrastructure are already emerging worldwide.
A New Approach to Asphalt Concrete Testing
Even in asphalt concrete testing, although materials and production are constantly evolving, we still rely on methods whose basic principles were established a century ago, says Aivars Kļavinskis, a master’s student at the Institute of Civil Engineering within the Faculty of Civil and Mechanical Engineering, to industry representatives.
He points out that the bitumen used in the production of asphalt concrete is not «simply a black, sticky mass»; depending on various factors – primarily temperature and load – it can vary from solid to liquid, making it highly suitable for road construction, so a conventional mechanical approach is insufficient to describe it. «It is important for us to ensure that during production, the bitumen is sufficiently fluid to mix with the mineral aggregate, coating it evenly, and sufficiently plastic to facilitate paving, and that during operation in summer heat it is sufficiently rigid and elastic to withstand traffic loads and prevent rutting, yet not too rigid and with good stress relaxation capabilities so it does not crack in winter. This is where rheology comes in – the science of a material’s flow and deformation,» continues A. Kļavinskis. The most common instrument for determining rheological properties is the dynamic shear rheometer (DSR), but its use for evaluating asphalt concrete performance at low temperatures is currently limited. A. Kļavinskis is researching how to assess performance at low temperatures using stress relaxation tests. The principle behind this is based on the assumption that stiffness is not the main cause of bitumen cracking, but rather the inability to sufficiently relax stress. This is a modern method that provides an in-depth study of road construction materials, helping to understand their behavior and the mechanisms behind it.
A. Kļavinskis is the first RTU master’s student to spend three months conducting experiments and tests at Empa laboratories in Switzerland as part of his thesis. According to him, the test results are promising.

Photo: “Latvijas Valsts ceļi”
Gauging industry feedback
Meanwhile, at a meeting of the LACHMAT Advisory Board, A. Kavlaks and A. Kļavinskis, along with other master’s students, doctoral students, and postdoctoral researchers – Rūta Anna Kinta, a master’s student at the Faculty of Civil Engineering and Mechanical Engineering; doctoral students Romāns Kornišovs and Dāvis Dragons; Nauris Silkāns, a doctoral student at the Faculty of Computer Science, Information Technology and Energy, and Juris Bitenieks, a senior researcher at the Institute of Chemistry and Chemical Technology, Faculty of Natural Sciences and Technologies, RTU – presented the progress made in their research and knowledge transfer. Their research covers a wide range of topics – from bitumen modification with lignin and sustainable solutions for the reuse of asphalt concrete pavement to the creation of 3D-printed concrete from local raw materials and data-driven methods for extending the life cycle of asphalt pavement.
Students and researchers also listen to industry proposals, particularly regarding the transfer of knowledge and technology to industry.
The Advisory Board was established to ensure that LACHMAT’s results align with the needs of the sector. The council includes Jānis Barbars, Head of the Research Management and Development Division at the Road Competence Center of «Latvijas Valsts ceļi»; Rolands Cepurītis, the Chairman of the Board of the Latvian Concrete Association and Chief Technology Officer at SIA «Primekss»; Jānis Zāle, Member of the Board of the Latvian Concrete Association and Head of Material Quality and Product Technology Department at SIA «Schwenk Latvija» and Monta Berga, Executive Director of the association «Latvian Road Builder».

Mārtiņš Zaumanis, leader of the Empa bituminous materials group and scientific project leader in Switzerland, is also participating in the road sector conference organized by «Latvijas Valsts ceļi» and the LACHMAT Advisory Board meeting.
The LACHMAT project, part of the Swiss-Latvian cooperation program «Applied Research», promotes research and innovation in the field of advanced materials, focusing on innovative approaches to smart concrete and asphalt. The «Applied Research» program is part of Switzerland’s contribution to European Union member states to strengthen research excellence and the knowledge base for innovation in Latvia, as well as to promote economic transformation and sustainable growth. The program allocates more than 12 million euros for the development of science and research in Latvia, of which 85% or approximately 10.5 million euros – is Swiss funding, while 15% is co-financing from the Latvian budget.